Acrylic paint for facade finish: concrete, plaster, asbestos cement, brick masonry and other surfaces made from mineral building materials.
For finishing building’s facades of mineral construction materials (concrete, plaster, filled, brick masonry, etc.)
4-5 m²/l, applied in 2 layers. The exact coverage rate is determined by covering the test area.
Purpose: for exterior use
Binder: modified styrene acrylic copolymer
Solvent: water
Color: white or tinted by color cards
Density: 1,38-1,41 g/cm³ (depending on the paint base)
pH: 8,0-9,0
Volatile organic compounds (VOC): <30 g/l EN ISO 11890-2
Non-volatile-matter content by volume: 35,0-47,0 % (depending on the paint base)
Classes for grain size (S): class S1, fine (<100 μm) EN 1062-1
Dry film thickness (E): class E2 >50 and ≤100 μm EN 1062-1
Degree of gloss, 85⁰: ≤10 (matt) EN 1062-1
Liquid water permeability W, kg/(m2*h0,5): ≤0,1 EN 1062-3; W3 class (low) EN 1062-1
Water vapour transmission rate, Sd, m: ≥0,14 and <1,4 EN ISO 7783-2; V2 class (medium) EN 1062-1
The loss of thickness of the coat (after 200 scrubs): ≥5 and <20 µm EN ISO 11998; Class 2 for wet-scrub resistance according to EN 13300
Work tools: brush, roller, spraying gun
Tool cleaning: with water
Application conditions: +10 °C to +25 °C and (35–80) % relative humidity. Do not paint in very hot, cold, humid (rain, dew, fog) and windy weather, avoid direct sunlight. Failure to follow these recommendations, may form poor-quality paint film.
Coverage rate: 4-5 m²/l, applied in 2 layers
Drying time (23 °C, 50 % RH): dust does not stick after 1 hour. Repainting can be done only after the first layer is completely dry (after ~2-4 hours), depending on surface, layer thickness, air temperature, humidity, etc.
Surface preparation.
The surface must be stable, dry and clean.
Unpainted surfaces: remove the dust, mud, grease, salts. Wash dirty building facades with a high-pressure water jet or sandblast. Prime porous and moisture-absorbing surfaces primed with IGIS AG deep primer or Taktika P deep primer.
Plaster mortars. Do not paint the new plaster surface for 2-4 weeks. Plaster needs to be fully dry prior to painting. Prime highly absorbent, porous, crumbling surfaces with IGIS AG deep primer or Taktika P deep primer.
Brick masonry. Clean the masonry of salts and do not leave cracks on it. Use facade paint on frost-resistant facade bricks.
Previously painted surfaces: remove the old peeling paint coating, wipe the crumbling surface to a firm base. Treat the surface affected by fungi and mold with an anti-mold agent. If necessary, prime the surface with IGIS AG deep primer.
Application
Stir well before use. Apply 1-2 layers. Paint of the same batch shall be used to cover one surface. Stir them in one tare to ensure color uniformity.
Paint large areas without interruption in the same direction throughout the wall. An even, high-quality coating is obtained by abundantly soaking the roller in the paint. Make sure there is enough paint on the roller during painting.
Maintenance
The surface film acquires full strength and can be cleaned after 28 days. Clean dirty painted surface with clean lukewarm water and a soft cloth or sponge. Hot water can soften the paint film. We recommend to clean with a mild alkaline cleaners (pH 6-8). Cleaners containing organic solvents are not suitable. Do not use abrasive cleaners such as rough sponges or brushes.
Precautionary statements: keep out of reach of children, avoid release to the environment, wear protective gloves/ protective clothing/eye protective/face protective. IF ON SKIN: wash with plenty of soap and water. IF IN EYES: rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
Additional hazard information: EUH208 – contains a mixture of 5-chlor-2-metil-2H-izotiazol-3-one and 2-metil-2H-izotiazol -3-one (3:1), 1,2-benzisothiazol-3(2H)-one can cause allergy in humans.
Shelf life in tightly closed original packaging: 24 months from the date of manufacture.
Storage and transportation conditions: store the product tightly closed in dry well-ventilated place at a temperature of +5 ⁰C to +30 ⁰C, protect against from damage, frost and direct sunlight.
Waste management
Do not pour into drains, water or soil. Empty, dry product package should be recycled or disposed of in accordance with national law.
Packing:
Igis F A and C bases:
0,9 l; 2,7 l; 9 l buckets
